Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
- Settings and routine maintenance of the car
Schedule of routine maintenance
General information about settings and adjustments
Check of levels of liquids
Check of a condition of tires and pressure of their rating
Check of level of the AT working liquid
Check of level of liquid of the power steering
Replacement of impellent oil and oil filter
Check, service and battery room charging
Check of a condition of components of system of cooling
Check of a condition and replacement of the hoses located in an impellent compartment
Check of a condition and replacement of brushes of screen wipers
Rotation of wheels
Check of a condition of components of a suspension bracket and steering drive
Greasing of components of the chassis
Check of a condition of components of system of production of the fulfilled gases
Check of level of greasing in a transfer case
Check of level of greasing of differential
Check of a condition of seat belts
Check and adjustment of turns of idling
Check of a condition of protective covers of power shafts
Check and replacement of the valve of system of operated ventilation of a case (PCV)
Replacement of a filtering element of an air purifier
Condition check, adjustment of effort of a tension and replacement of driving belts
Check of a condition of components of a power supply system
Check of brake system
Adjustment of height of situation and free wheeling of a pedal of a brake
Check of a condition and replacement of spark plugs (petrol engines)
Check and adjustment of gaps of valves
Replacement of the fuel filter
Check and service of the conditioner of air (To/in)
Service of system of cooling
Condition check, stuffing by greasing and adjustment of forward naves and wheel bearings
Replacement of ATF of automatic transmission and main transfer
Replacement of greasing of a transfer case
Replacement of greasing of differential
Check of a condition of components of system of catching of fuel evaporations
Check of serviceability of a condition of components of system of a retsirkulyatsiya of the fulfilled gases (EGR)
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
+ Onboard electric equipment
Greasing of components of the chassis
Points of greasing of kardanny driveshafts
||1. Prepare a necessary stock of greasing of a demanded grade (see. Specifications) and the lubricant gun for stuffing of hollow components (address to an accompanying illustration):
1 — Liquid impellent oil;
2 — the Graphite aerosol;
3 — Greasing;
4 — the Lubricant gun.
2. Having glanced under the car, find lubricant unions of components of a steering drive, a suspension bracket and the transmission line (address to an illustration at the beginning of the Section). Usually unions enter into a regular complete set of such knots, as tips of steering drafts and kardanny hinges. If instead of unions caps are established, instead of them it is necessary to screw the prepared shtutserny nozzles (see paragraph 1).
On some knots instead of lubricant unions can appear caps are established, take care also of existence near at hand a set of unions, carving shtutserny nozzles of the various form providing adequate access practically to any component are issued.
3. To Poddomkratta the car also establish it on props, or tire out its lift.
4. For pro-cleaning of a nozzle of the gun from dirt squeeze out a little greasing. Wipe a nozzle pure rags.
If assume to make at this stage rotation of wheels, do not forget to weaken fixing nuts before they will be torn off from the earth.
5. Prepare a stock of rags and start stuffing of components by greasing.
6. Wipe the lubricant union and a surface of a component surrounding it pure rags, connect to the union a nozzle of the gun and start stuffing. Continue to pump greasing until it will not start to exude through joints of landing surfaces of a component.
7. Rags collect from a component surface excess of greasing and pass to stuffing of the following knot.
If greasing starts to exude through a gun nozzle, it is necessary to clean and give particular attention it to clip density. In case of need replace the union.
8. Stuffing of a sliding collar of the universal hinge of the driveshaft continue until greasing will not start to exude through an assembly epiploon (address to an accompanying illustration).
10. Without getting out from under the car, wipe cables of a drive of the parking brake and with fingers grease their directing and executive levers.
||9. When stuffing kardanny hinges of usual type greasing should start to exude through joints of components of assembly (address to an accompanying illustration).
12. Open a cowl and fill a little greasing for the chassis in the mechanism of a latch of the lock. Ask the assistant to extend against the stop the lever of an otpuskaniye of the lock of a cowl under the dashboard and grease all being bared surfaces of a driving cable.
||11. At the corresponding complete set of the car put greasing on a lithium basis on contact surfaces of persistent arms and adjusting bolts of assemblies of rotary fists (address to an accompanying illustration).
13. With liquid impellent oil grease loops of all doors and a cowl.
14. For greasing of key cylinders it is most convenient to use the graphite greasing delivered in aerosol ballonchik, – ask in shops of automobile accessories.
15. With silicone greasing grease sealing tapes of doors for the purpose of protection them from premature wear.