|
|
Toyota Land Cruiser 100/Amazon, Lexus LX 470since 1997 of releaseRepair and car operation |
|
|
Toyota Land Cruiser, Amazon, LX470 Lexus + Identification numbers of the car + Governing bodies and receptions of safe operation of the car + Settings and routine maintenance of the car + Engine + Systems of cooling of the engine, salon and air conditioning heating + the Power supply system and production of the fulfilled gases + engine Electric equipment + Control systems of the engine and decrease in toxicity of the fulfilled gases + gear shifting Box + Transmission line + Brake system - Suspension bracket and steering Specifications Removal and installation of forward shock-absorbers Removal and installation of the forward stabilizer of cross-section stability Removal and installation of assembly of a rotary fist with a nave Check of a condition and replacement of spherical support Removal and installation of torsionny bars Removal and installation of the top managing director of the lever of a forward suspension bracket Removal and installation of the bottom managing director of the lever of a forward suspension bracket Removal and installation of back shock-absorbers Removal and installation of a bar of the back stabilizer of cross-section stability Removal and installation of a jet bar Removal and installation of a screw spring of a back suspension bracket Removal and installation of levers of a back suspension bracket Removal and installation of a steering wheel Condition check, removal and installation of drafts of a steering drive Replacement of protective covers of assembly of the steering mechanism Removal and installation of the steering mechanism Removal and installation of the steering pump Air removal from a hydraulic path of system of strengthening of a wheel Wheels and tires - the general information Corners of installation of wheels + Body + Onboard electric equipment |
Suspension bracket and steering Forward suspension bracket The forward suspension bracket has an independent design. Rotary fists are connected by the top and bottom levers of a suspension bracket (operating levers) by means of spherical support. The opposite ends levers приболчены to a frame. The stabilizer of cross-section stability reducing rocking and a list of the car on turns enters into a regular complete set. Instead of screw springs torsionny bars which fasten to the top levers of a suspension bracket are used. Back suspension bracket Components of a back suspension bracket The back suspension bracket is organized by means of pair of the screw springs, two telescopic shock-absorbers, four levers (two bottom and two top) and the jet bar connecting the left end of the bridge to a beam of the bearing frame. The bar of the stabilizer of cross-section stability приболчена to assembly of the back bridge also fastens to a car frame by means of two racks (address to an illustration above). Steering drive Considered models are equipped with the hydrostrengthened steering transfer of reechny type connected to rotary fists by means of two steering drafts. The case of the mechanism fastens to a cross-section beam. Often in the course of service of components of a suspension bracket and a steering drive it is necessary to face fixture resistant to an otdavaniye.« By Prikipaniye» elements of fixture it is connected with that they are constantly subject to external influences, are in contact to water, dirt, a soot and other promoting development of corrosion by substances. For the purpose of simplification of procedure of an otdavaniye of its such "become attached" fixture it is necessary to impregnate with plentiful amount of getting oil beforehand. Cleaning of open carving parts of fixture by a rigid wire brush also promotes simplification of an otdavaniye of prirzhavevshy nuts. Sometimes, in especially hard cases, for an otpuskaniye "become attached" bolts/nuts it is possible to use a drift. The drift rests against the region of a shliyets of a nut/head of a bolt, then sharp blows are struck to its opposite end with a hammer. Watch that the drift did not break, try not to damage in inexact blows a carving. Quite effective way is also warming up of fixture resistant to an otdavaniye and a surface of a component surrounding it a torch of a blowtorch or a gas torch though originators of this Management and do not recommend to resort without extreme need to such technology in view of its potential danger connected with possibility of ignition and risk of receiving burns. Different extension pieces, collars and trumpet nozzles are intended for increase in a torque at an otpuskaniye of fixture on them. However, remember that it is not necessary to use such intensifying adaptations complete with the drive equipped with "graggers" – the risk of failure of the ratchet mechanism is too great. Sometimes the "become attached" fixture starts to give in after previously slightly will be tightened clockwise. All fixture, which otpuskaniye demanded application of extraordinary measures at assembly is subject to replacement!
As procedures of service of components of a suspension bracket are carried out under the car, it is necessary to take care in advance of possibilities of lifting of a vehicle and its fixing in the lifted situation (prepare reliable a jack and props).
|
|