Toyota Land Cruiser, Amazon, LX470 Lexus + Identification numbers of the car + Governing bodies and receptions of safe operation of the car + Settings and routine maintenance of the car + Engine + Systems of cooling of the engine, salon and air conditioning heating + the Power supply system and production of the fulfilled gases + engine Electric equipment + Control systems of the engine and decrease in toxicity of the fulfilled gases + gear shifting Box + Transmission line + Brake system - Suspension bracket and steering Specifications Removal and installation of forward shock-absorbers Removal and installation of the forward stabilizer of cross-section stability Removal and installation of assembly of a rotary fist with a nave Check of a condition and replacement of spherical support Removal and installation of torsionny bars Removal and installation of the top managing director of the lever of a forward suspension bracket Removal and installation of the bottom managing director of the lever of a forward suspension bracket Removal and installation of back shock-absorbers Removal and installation of a bar of the back stabilizer of cross-section stability Removal and installation of a jet bar Removal and installation of a screw spring of a back suspension bracket Removal and installation of levers of a back suspension bracket Removal and installation of a steering wheel Condition check, removal and installation of drafts of a steering drive Replacement of protective covers of assembly of the steering mechanism Removal and installation of the steering mechanism Removal and installation of the steering pump Air removal from a hydraulic path of system of strengthening of a wheel Wheels and tires - the general information Corners of installation of wheels + Body + Onboard electric equipment
|
Condition check, removal and installation of drafts of a steering drive
Check
Details of installation of components of a steering drive
|
1. By means of steering drafts the effort is transferred to operated forward wheels of the car (address to an illustration above). The demanded geometry of interposition of wheels taking into account a difference of internal and external radiuses of turn is thus observed. The steering drive consists of the steering mechanism and two adjustable lateral steering drafts. Progress by means of two adjustable lateral drafts is transferred to rotary fists of stupichny assemblies of forward wheels. Lateral drafts are equipped since both ends with spherical tips and the adjusting tubular coupling in the middle. The coupling is fixed by means of two collars. 2. Bring forward wheels of the car into rectilinear situation and the ignition key block a steering column. 3. To Poddomkratta one of the car parties so that the corresponding forward wheel came off the earth on 2-3 see. 4. Fix the tsiferblatny indicator so that its plunzher rested against a forward rim of a wheel, then grasp a wheel hands in provisions on 3 both at 9 o'clock and strongly pull it forward-back. Consider the indicator indication, it should not exceed value of 2.7 mm. At excessive size люфта attentively check a condition of all stykovochny and rotary knots of a drive of the steering mechanism. In case of need tighten the corresponding fixture and replace defective components. 5. Check a condition of protective covers of spherical hinges, estimate freedom of rotation of tips of steering drafts, make visual survey of components of a steering drive about identification of deformations and signs of mechanical damages. |
|
Removal and installation
Steering drafts
|
1. Cock the parking brake. Weaken nuts of fastening of the corresponding forward wheel. To Poddomkratta a car front also establish it on props. Remove a wheel. 2. Take шплинт and weaken, but do not turn on up to the end koronchaty nut of a spherical finger of a tip of draft needing replacement.
|
3a. In need of performance of replacement of a tip mark its situation (address to an illustration). |
|
3b. With the help 2-захватного a stripper liberate a tip from assembly of a rotary fist. Completely unscrew a koronchaty nut and separate a tip from a fist (address to an illustration). |
4. If all draft needs replacement, separate a tip from assembly of an intermediate shaft (see paragraphs 2 and 3). 5. Before performance of replacement measure distance from a cut of the adjusting coupling to the central point of a spherical finger of a tip. Result of measurement write down, then weaken collars of fastening of the coupling and turn out a tip. 6. Grease a carving part of a new tip with greasing for the chassis. Screw a tip in the coupling on former depth (see paragraph 5).
|
The quantity of visible rounds of a carving of one tip should not differ from quantity of visible rounds of a carving of the second more than on three. Do not tighten while fixing collars. |
7. Screw a koronchaty nut of a spherical finger of a tip, tighten it with demanded effort and fix shplinty, having in case of need tightened a nut a little more for combination of openings under installation шплинта.
|
If the sharovy finger starts to be turned at a nut tightening, press in a conic nest big nippers. |
8. Tighten nuts of fixing collars. The bolt should appear will develop almost horizontally, and a groove of the adjusting coupling – рассовмещен with locks of collars. 9. Establish to the place of a wheel, lower the car on the earth and tighten wheel nuts with demanded effort (see. Head of Control and routine maintenance of the car). Drive away the car on car repair shop for carrying out check and adjustment of corners of installation of forward wheels. |
|
|
|