Repair and Toyota Land Cruiser 100/Amazon, Lexus LX 470 car operation - Removal and installation of a driving disk//Toyota Land Cruiser, Amazon, LX470 Lexus / avto2tyning.ru

Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 of release

Repair and car operation



Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
+ Settings and routine maintenance of the car
- Engine
   + Typical procedures of service of engines
   - Procedures of service of the petrol engine
      Removal and installation of covers of heads of cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of final collectors
      Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Replacement of a forward epiploon (ов) cranked shaft / camshafts
      Replacement of a back epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of valves
      Removal and installation of heads of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and installation of a driving disk
      Check of a condition and replacement of support of an engine mount
   + Procedures of service of the diesel engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of a driving disk

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

To Poddomkratta the car also establish it on props. Remove transmission (see. Head gear shifting Box).
2. By means of a center punch or a marker mark the provision of a driving disk in relation to an end face of a cranked shaft.
3. Turn out bolts of fastening of a driving disk to a cranked shaft. If in the course of weakening of bolts the shaft starts to be turned, get a screw-driver in teeths of a wreath of a flywheel.


4. Remove assembly of a driving disk from a cranked shaft.

The weight of assembly is very considerable, - it will be reasonable to resort to the help of the assistant. Put on working gloves not to cut a hand about keen edges of teeths of a wreath. Remove also established from both parties of a driving disk remote plates, try to remember an order of installation of components.

Installation

 PERFORMANCE ORDER

1. Carefully degrease assembly of a driving disk and check it working surfaces on existence of cracks, the furrows left heads of rivets, traces of an overheat and other damages. Insignificant defects can be removed by means of a fine-grained emery paper, in more serious cases assembly is subject to replacement. Check a condition of teeths of a wreath, having laid assembly of a driving disk on a flat surface, estimate size of its not planeness.
2. Smooth out and examine interfaced surfaces of a driving disk and a pin of a cranked shaft. In case of need make replacement of a back epiploon (see. Section Replacement of a back epiploon of a cranked shaft).
3. Remove traces of old hermetic from bolts and boltovy openings.

If completely to clear bolts it is not possible, replace them new on which hermetic to put any more does not follow.

4. Do not forget to establish remote plates. Track correctness of combination of the components of landing labels put in the course of dismantle. Before rolling fixing bolts, grease their carving part with fixing hermetic.
5. Having blocked a driving disk from a provorachivaniye (see paragraph 3), in a diagonal order tighten fixing bolts with demanded effort.
6. Further installation is made as it should be the return to an order of dismantle of components.