Repair and Toyota Land Cruiser 100/Amazon, Lexus LX 470 car operation - Removal and installation of covers of heads of cylinders//Toyota Land Cruiser, Amazon, LX470 Lexus / avto2tyning.ru

Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 of release

Repair and car operation



Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
+ Settings and routine maintenance of the car
- Engine
   + Typical procedures of service of engines
   - Procedures of service of the petrol engine
      Removal and installation of covers of heads of cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of final collectors
      Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Replacement of a forward epiploon (ов) cranked shaft / camshafts
      Replacement of a back epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of valves
      Removal and installation of heads of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and installation of a driving disk
      Check of a condition and replacement of support of an engine mount
   + Procedures of service of the diesel engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of covers of heads of cylinders

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Unscrew four bolts of fastening of coils of ignition to a klapanny cover put marking and remove coils.
3. From the driver's party:
  1. To removal of a cover can stir щуп measurements of level of impellent oil – take out it and put aside.
  2. Move fuel highways and hoses of ventilation of a coal adsorber that did not disturb. Needs for their detachment should not arise.
  3. Disconnect a hose of ventilation of a case.

4. From the passenger party (on the right):

  1. Disconnect G-shaped case ventilation.
  2. Unfasten the vacuum hose of GUR conducting to the inlet pipeline, and take him aside.
5. Give nine bolts of fastening of a cover of a head of cylinders and accurately remove it. Be accurate: an aluminum cover easy on to harm. If the cover "became attached" and does not give in to removal, обстучите it on perimeter a hammer through wooden whetstone, in case of need use a shpatel or a knife with a thin edge for cutting of a layer of the dried-up hermetic.

In order to avoid development of leaks, at all do not hook a cover the lever under an interfaced surface!

Installation

 PERFORMANCE ORDER

1. Interfaced surfaces of heads of cylinders and their covers should be absolutely pure and dry. By means of a scraper remove all traces of old hermetic and fragments of the destroyed laying, then wipe surfaces the rags moistened in acetone. Presence on interfaced surfaces of traces of oil can lead to development of leaks.
2. Fill in the landing grooves segment rubber jams, having made sure of their suitability. Grease them with FIPG hermetic (Toyota No. 08826-00080), with the same hermetic fill two points in a head of cylinders at once behind covers of a belt of a drive of GRM (address to an accompanying illustration). Note the provision of these points before cleaning to put new hermetic there.

3. Densely plant in a reception flute sealing laying and press a cover to a head of cylinders. Establish sealing washers, screw fixture.
4. In three-four stages tighten fixture with demanded effort (6 Nanometers).
5. Installation of the remained components is made as it should be, the return to an order of their dismantle.