Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 of release

Repair and car operation



Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
+ Settings and routine maintenance of the car
+ Engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of a decorative front grille
   Removal and installation of forward and back bumpers
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of external rear-view mirrors
   Removal, installation and adjustment of doors
   Removal and installation of forward wings
   Removal, installation and adjustment of a door of a back
   Removal and installation flew down also a regulator of a window regulator of a door of a back
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of latches, zamkovy cylinders and door handles
   Removal and installation of a cover of the top hatch with a drive
   Removal and installation of a casing of a steering column
   Removal and installation of the central console
   Removal and installation finishing and main dashboard sections
   Removal and installation of a lattice of an air inlet of a forward fairing
   Removal and installation of seats
   Removal and installation of an internal rear-view mirror
+ Onboard electric equipment




Removal and installation finishing and main dashboard sections

Models of cars considered in the real Management are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation.

Dashboard design


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Disconnect safety cushions (see. Onboard electric equipment).
3. Remove a steering wheel (see. Head Suspension bracket and steering).
4. Remove a casing of a steering column (see. Section Removal and installation of a casing of a steering column).
5. Paste over with a protective film of an overlay of forward racks (address to an illustration above), it will protect them at removal.
6. Remove handles of opening of a cowl and the hatch of a fuel tank.
7. Uncover the block of safety locks.
8. Give fixture of the bottom central cover and remove it.
9. Disconnect an air line No. 2.
10. Give fixture of the DLC No. 3 socket and the block of safety locks.
11. Remove the bottom panel No. 1.
12. Remove an overlay of a combination of devices and remove a combination of devices.
13. Remove the bottom overlay of the central section of furnish of the dashboard together with hours.
14. Having wound a screw-driver with an insulating tape, unhook 2 latches and remove a coaster.
15. Remove an ashtray.
16. Give fixture central section of furnish of the dashboard with the control panel a heater and disconnect conducting.
17. Turn out screws of fastening of the control panel a back heater.
18. Remove a radio tape recorder, a cover of a ware box, the panel of a loudspeaker and a loudspeaker, forward and back sections of the central console.
19. Unscrew 5 screws and 9 bolts of fastening of the main section of the dashboard.
20. Remove an intensifying bar, an arm and the main section of the dashboard.
21. Installation is made upside-down.