Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 of release

Repair and car operation



Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
+ Settings and routine maintenance of the car
+ Engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of a decorative front grille
   Removal and installation of forward and back bumpers
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of external rear-view mirrors
   Removal, installation and adjustment of doors
   Removal and installation of forward wings
   Removal, installation and adjustment of a door of a back
   Removal and installation flew down also a regulator of a window regulator of a door of a back
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of latches, zamkovy cylinders and door handles
   Removal and installation of a cover of the top hatch with a drive
   Removal and installation of a casing of a steering column
   Removal and installation of the central console
   Removal and installation finishing and main dashboard sections
   Removal and installation of a lattice of an air inlet of a forward fairing
   Removal and installation of seats
   Removal and installation of an internal rear-view mirror
+ Onboard electric equipment



Removal, installation and adjustment of doors

Removal and installation

Forward door and its components


Doors of the car have considerable weight therefore it will be reasonable to secure with the help of the assistant.


In order to avoid receiving cuts of hands about edges of technological windows in a doorframe work in gloves!


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove the panel of an internal upholstery and the film vlagozashchitny screen (see. Section Removal and installation of panels of an internal upholstery of doors). At the corresponding complete set disunite contact sockets and liberate from intermediate clamps electroconducting of the actuation mechanisms located in a doorframe.

Previously it is meaningful to mark disconnected wires.

3. Open a door against the stop and prop up it a jack, or wooden blocks.

In order to avoid damage of LKP lay between a head of a jack and door edge a rags layer.

4. Lead round loopy levels a marker, having marked their situation on a body element. Turn out fixing bolts (address to an illustration above) and by means of the assistant accurately remove door assembly from the car. If the door is subject to replacement only, to remove loops from a rack does not follow.
5. Installation is made upside-down, track combination of the landing labels put in the course of dismantle. In case of need make adjustment.
6. Strongly tighten fixing bolts of loopy levels.

Adjustment

 PERFORMANCE ORDER

1. Adjustment of provision of a door in the plane of an aperture is carried out by means of shift of loops concerning a body. For this purpose it is necessary to weaken bolts of fastening of loops to a rack.
2. Adjustment of a ledge of a door from a body is carried out by means of door shift concerning loops. For this purpose it is necessary to weaken bolts of fastening of a door to loops.
3. Serviceable operation of the locking mechanism after installation of a door can achieve by correction of position of the drummer of the lock in the vertical direction. For an assessment of size of shift lead round a plate of the basis of the drummer a marker. Weaken fixture and make necessary adjustment, the latch should enter into gearing with the central part of the drummer. In summary adjust position of the drummer in the horizontal direction, the closed door should appear aflush with a surface of the rack/panel of a back wing and regularly thus to be locked.