Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 of release

Repair and car operation



Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
+ Settings and routine maintenance of the car
+ Engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
- Brake system
   Specifications
   System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
   Replacement of brake shoes
   Removal and installation of supports of disk brake mechanisms
   Condition check, removal and installation of a brake disk
   Removal and installation of the main brake cylinder (GTTs)
   Check of a condition and replacement of brake lines and hoses
   Sensitive to loading / перепускной the valve (LSP & BP)
   Adjustment of the parking brake
   Replacement of cables of a drive of the parking brake
   Check of serviceability of functioning / tightness, removal and installation of the amplifier of brakes
   Pumping of brake system
   Adjustment of a pedal of a foot brake
   Check of serviceability of functioning and replacement of the sensor switch of stoplights
   Sensors and ABS system activator
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Replacement of brake shoes

Replacement of brake shoes should be made at the same time on both forward/back brake mechanisms. Remember that developed in the course of operation of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system gasoline or solvents on an oil basis, apply only firm cleaners or methyl alcohol!

Details of installation of forward brake shoes and support

1 — the pumping Union
2 — the External antivizgovy slip
3 — Lock rings
4 — the Internal antivizgovy slip
5 — the Spring clamp
6 — the Internal brake shoe
7 — the Brake support

8 — the Boot
9 — the Piston
10 — a piston Cuff
11 — Antivizgovaya a spring
12 — the External brake shoe
13 — the Directing pin

Details of installation of back brake shoes and support

1 — the Antisplash guard
2 — the pumping Union
3 — the Main directing pin
4 — the Brake support
5 — Laying
6 — the Plug of the main directing pin
7 — the Plug of an auxiliary directing pin
8, 11 — the Brake shoe
9, 13 — the Holding lamellar loose leaf
10 — the wear Indicator

12, 14 — Antivizgovaya a slip
15, 21 — the Cap
16 — a support Bracket
17 — the Lock ring
18 — the Boot
19 — the Piston
10 — a piston Cuff
11 — Antivizgovaya a spring
22 — the Auxiliary directing pin


 PERFORMANCE ORDER

1. Details of installation of brake shoes are presented on illustrations above. Weaken nuts of fastening of forward wheels. To Poddomkratta a car front also establish it on props. Cock a lay brake / prop up protivootkatny boots wheels standing on the earth. Remove wheels.
2. Remove the spring clamp, directing pins, an antivizgovy spring, blocks and antivizgovy slips.
3. After block extraction attentively examine internal surfaces of a support on existence of signs of development of leakages of brake liquid, check a condition of a boot of the piston. Defective components are subject to replacement (see. Section Removal and installation of supports of disk brake mechanisms). Do not forget to study also attentively a condition of a brake disk (see. The section condition Check, removal and installation of a brake disk), in case of need send him to a pro-point.
4. Pump out a little brake liquid from the GTTs tank and wring out pistons in cylinders by means of a hammer or mount (address to an accompanying illustration).

It is necessary to wind mount with an insulating tape. Make replacement on each support serially. For simplification of moving of the piston weaken the union of pumping and move pistons at small leakage of brake liquid.

5. Establish new antivizgovy overlays for new blocks and establish two blocks.

Put greasing for disk brakes on both parties of internal antivizgovy slips. Greasing should not get on a working surface of blocks or a disk.

6. Establish the antivizgovy spring, directing pins and a spring clamp.
7. Having finished service of both brake mechanisms, establish to the place of a wheel, lower the car on the earth and tighten wheel nuts with demanded effort (see. Head of Control and routine maintenance of the car).
8. Check level of brake liquid in the GTTs tank, in case of need make the corresponding adjustment (see. Head of Control and routine maintenance of the car). Several times rock a pedal of a foot brake for a usadka of blocks on disks, then repeat check of level of liquid.
9. Before starting operation of the car make sure of serviceability of functioning of brake system.