Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
+ Settings and routine maintenance of the car
- Engine
+ Typical procedures of service of engines
+ Procedures of service of the petrol engine
- Procedures of service of the diesel engine
Removal, installation, dismantling and assembly of a head of cylinders
Removal and installation of the inlet pipeline and final collector
Removal, check of a condition and installation of a belt of a drive of GRM
Removal and installation of cogwheels of a drive of GRM
Replacement of a forward epiploon of a cranked shaft and camshaft and TNVD epiploons
Replacement of a back epiploon of a cranked shaft
Removal and installation of camshafts and pushers of valves
Removal and installation of the pallet of a case of the engine
Removal, check of a condition and installation of the oil pump
Removal and installation of a maslookhladitel
Removal and installation of a driving disk
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, check of a condition and installation of a belt of a drive of GRM
Removal
|
|
Exact observance of phases of a gazoraspredeleniye is very important, but for DOHC engines important extremely. Incorrect installation of phases can seriously damage the engine. Be accurate at installation of a belt of a drive of GRM and before the first start after repair once again check coincidence of labels.
|
|
|
Do not turn cranked or camshafts at the removed GRM belt, and also do not turn the engine for cogwheels of camshafts. Turn the engine only in its normal direction (clockwise).
|
Assembly of a drive of GRM
|
|
1. Disconnect a negative wire from the battery.
|
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! |
2. Turn out spark plugs.
3. Remove all components disturbing to removal of a cover of a GRM belt.
4. Uncover (1) GRM belt (address to an illustration above).
5. Turn a cranked shaft clockwise and level adjusting labels (2).
6. Make sure that labels (4) too coincided.
7. Give and completely turn out bolts of fastening of assembly of a natyazhitel of a GRM belt.
8. Remove assembly of a natyazhitel (6), turn out a bolt (7) pulleys of a natyazhitel and remove a pulley (8).
9. Remove a belt of a drive of GRM. |
|
Check See the check description for the engine 2UZ-FE (The section Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM).
Installation
|
|
1. Fix a rod of a natyazhitel of a belt of a drive of GRM, крошев a hairpin in thickness of 1.5 mm in openings in a rod and the natyazhitel.
2. Put on a GRM belt pulleys and make sure that adjusting labels coincide.
3. Establish a pulley of a natyazhitel and tighten bolts of his fastening with effort of 34 Nanometers.
4. Establish a natyazhitel and tighten bolts of his fastening with effort of 13 Nanometers.
5. Take out a lock hairpin, thereby having pulled a belt.
6. Turn a cranked shaft on two turns clockwise. Make sure that adjusting labels coincide. Otherwise repeat procedure of installation and a GRM belt tension.
7. Establish other acting in film components upside-down. Tighten fixture with demanded effort.
8. Dump indications To/l replacement of a belt of a drive of GRM. For this purpose address on HUNDRED Toyotas.
9. After replacement of a belt of a drive of GRM check operation of the fuel pump of a high pressure. |
|
|
|