Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 of release

Repair and car operation



Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
+ Settings and routine maintenance of the car
- Engine
   + Typical procedures of service of engines
   + Procedures of service of the petrol engine
   - Procedures of service of the diesel engine
      Removal, installation, dismantling and assembly of a head of cylinders
      Removal and installation of the inlet pipeline and final collector
      Removal, check of a condition and installation of a belt of a drive of GRM
      Removal and installation of cogwheels of a drive of GRM
      Replacement of a forward epiploon of a cranked shaft and camshaft and TNVD epiploons
      Replacement of a back epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of valves
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and installation of a maslookhladitel
      Removal and installation of a driving disk
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Removal and installation of cogwheels of a drive of GRM

Drive components GRM (part 1)

1 — the Clip
2, 21 — the Vacuum hose
3, 28, 33, 34 — the Sealing washer
4 — the Cover of a gear belt
5 — the Flange No. 2
6 — the Clip
7 — the Flange No. 1
8 — a camshaft Cogwheel
9 — Natyazhitel of a gear belt
10 — the Tension roller
11 — the Flat washer
12 — the Clip (models with ERG system)
13 — a camshaft Cogwheel
14 — Shponka of a camshaft

15 — the Driving belt
16 — the Fan
17 — the Pulley of a drive of the water pump
18 — the Cover of a head of cylinders
19, 23, 27, 31 — Laying
20 — the Heater on an entrance
22 — the Inlet branch pipe
24 — Assembly of an inlet branch pipe
25 — an EGR valve Arm
26 — Termozashchitny the screen
29 — the Vacuum hose (models with ERG system)
30 — the Gear belt
32 — the Filter

Drive components GRM (part 2)

1 — the Sealing ring
2 — the Pulley of a cranked shaft
3 — the Forward epiploon of a cranked shaft
4 — the Epiploon of a cogwheel of TNVD
5 — the Persistent plate
6 — the Intermediate cogwheel
7 — the Cogwheel of a drive of the oil pump
8 — the Shaft of an intermediate cogwheel
9 — the Cogwheel of a drive of TNVD and GRM
10 — the Sealing ring
11 — the Bearing of a cogwheel of TNVD

12 — TNVD Cogwheel
13 — Termozashchitny the No. screen 2 blocks of cylinders
14 — a camshaft Epiploon
15 — the Back cover of a belt of a drive of GRM
16 — the Cover of cogwheels of a drive of GRM
17 — the Clip
18 — Laying
19 — the Arm
20 — the Oil tube
21 — Laying
22 — the Vacuum pump

Removal

 PERFORMANCE ORDER

1. Components of a drive of GRM are presented on illustrations above.
2. Remove a driving belt.
3. Remove a belt of a drive of GRM and cogwheels of camshafts
4. Remove a back cover of a belt of a drive of GRM
5. Turn out two fixing bolts and remove an oil pipeline of the vacuum pump
6. Remove the vacuum pump.
7. Block a cranked shaft and turn out the central bolt of its pulley (address to an accompanying illustration).
8. Remove a pro-rate and by means of a stripper dismantle a pulley of a cranked shaft.
9. Turn out 14 bolts of fastening of a cover of cogwheels of a drive of GRM.
10. Measure an axial gap of an intermediate cogwheel and if necessary replace its persistent plate, a shaft, or a cogwheel.
11. Remove a cogwheel of a drive of the oil pump by means of a stripper.
12. Turn out two bolts, remove a persistent plate, a cogwheel and its axis.
13. Block TNVD cogwheel, give a nut of its fastening and remove a cogwheel.

Bolts of a stripper roll no more, than on 8 mm.

14. Dismantle a cogwheel of a drive of TNVD and GRM.

Installation

 PERFORMANCE ORDER

1. Installation is made upside-down.
2. For installation of an intermediate cogwheel turn a leading cogwheel of TNVD so that the label «3» on a cogwheel of a cranked shaft was combined with a label «4» on a leading cogwheel of TNVD. Then enter cogwheels into gearing (address to an accompanying illustration).