Repair and Toyota Land Cruiser 100/Amazon, Lexus LX 470 car operation - Removal, check of a condition and installation of the oil pump//Toyota Land Cruiser, Amazon, LX470 Lexus / avto2tyning.ru

Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 of release

Repair and car operation



Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
+ Settings and routine maintenance of the car
- Engine
   + Typical procedures of service of engines
   + Procedures of service of the petrol engine
   - Procedures of service of the diesel engine
      Removal, installation, dismantling and assembly of a head of cylinders
      Removal and installation of the inlet pipeline and final collector
      Removal, check of a condition and installation of a belt of a drive of GRM
      Removal and installation of cogwheels of a drive of GRM
      Replacement of a forward epiploon of a cranked shaft and camshaft and TNVD epiploons
      Replacement of a back epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of valves
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and installation of a maslookhladitel
      Removal and installation of a driving disk
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal, check of a condition and installation of the oil pump

Removal

 PERFORMANCE ORDER

1. Remove the case pallet (see. Section Removal and installation of the pallet of a case of the engine).
2. Put adjusting labels on TNVD and the oil pump (address to an accompanying illustration).
3. Remove a final branch pipe of system of cooling.
4. Give fixture and remove the case of the oil pump (address to an accompanying illustration).
5. For dismantling of the pump take out its conducted gear wheel (address to an accompanying illustration), turn out a stopper of the reduktsionny valve and remove the valve, laying and a spring.
6. Scratch out from interfaced surfaces of the pump and the engine block all traces of hermetic and a material of old laying, then wipe surfaces the rags moistened in acetone.

Check

 PERFORMANCE ORDER

1. Wash out all components in solvent, then check them on existence of signs of excessive wear and mechanical damages.
2. Examine rubbing surfaces of components of the reduktsionny valve, estimate a condition of a klapanny spring. In case of need make valve replacement assembled.

Installation

 PERFORMANCE ORDER

1. Lay in the pump case conducting and conducted gear wheels marking towards a cover.
2. Grease components of the reduktsionny valve with pure impellent oil and establish them on the regular place. Tighten a stopper with new sealing laying.
3. Impose on an interfaced surface of the pump a RTV hermetic pillow (address to an accompanying illustration).
3. Impose new rubber consolidation (address to an accompanying illustration).

Installation of the pump should be complete within five minutes after hermetic imposing.

4. Tighten bolts of fastening of the case of the oil pump with effort of 20 Nanometers.
5. Establish TNVD, I am guided by the labels put earlier.
6. Turn out a stopper of the oil pump a six-sided key on 5 mm (address to an accompanying illustration) and fill in in the pump about 10 cm 3 impellent oils.
7. Grease a stopper carving with stiffening hermetic and screw a stopper into place.
8. Establish a maslopriyemnik with new laying.
9. Establish the case pallet.
10. Add necessary amount of engine oil, start the engine and check it on existence of signs of development of leaks.
11. Once again check level of impellent oil.