Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
- Governing bodies and receptions of safe operation of the car
Specifications
Instrument guard and signaling devices
Unlocking and locking of locks of the car, management of window regulators
Switches
Ignition switch, transmission and темпостат
Systems of ventilation, heating and air conditioning
Audiosystem
+ Settings and routine maintenance of the car
+ Engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Ignition lock, transmission and темпостат
Switch of ignition and blocking of a steering column
|
|
Never take out a key during car movement as it will lead to blocking of a steering wheel and driving loss. Do not leave a key in the situation "ON" if the engine does not work. Thus the accumulator can be discharged, and ignition can be damaged.
|
|
|
At a car complete set system of blocking of the engine, at a vynimaniye of a key the system of blocking of the engine will automatically work.
|
|
|
The ignition and blocking switch the helmsman of a column is located to the right of a steering column (address to an accompanying illustration). |
Below the description of position of the ignition key is provided in the lock.
«START» – starter inclusion. The key will return to the situation "ON" at an otpuskaniye.
«ON» – turning on of the engine and auxiliaries of all types. This normal situation when driving.
"ASS" – auxiliary devices, such as a radio receiver, work, however the engine is switched off.
«LOCK» – the engine is switched off, and the steering wheel is blocked. The key can be taken out only in this situation. It is necessary to press a key to turn it from the situation "ASS" in the situation "LOCK". If a key will take out, the system of blocking of the engine will be automatically established. At engine start the key can seem got stuck in the situation "LOCK" (blocking). For its release from this situation at first be convinced that the key is pressed against the stop, and then slightly повращайте a steering wheel, carefully turning a key.
Automatic transmission
The selector lever, switches of AT modes of the Toyota Land Cruiser model and their description it is provided on an accompanying illustration.
Governing bodies transmission of the Lexus LX models 470 see in Governing bodies and receptions of safe operation of the car.
|
|
When using regulator темпостата, even at inclusion of lowering transfer by switching off of raising transfer, braking by the engine will not be carried out, as is involved темпостат. |
System of distribution of a torque between driving wheels
System of blocking of interaxal differential
|
|
Use the lever of a choice of a mode and the switch of blocking of interaxal differential (address to an accompanying illustration) for a choice of the following modes of a transfer case and interaxal differential. |
"N" (position of raising transfers)
The position of "N" of the lever of a regulator of a full drive provides a mode of blocking or an unblocking of interaxal differential depending on a position of the corresponding button.
Use this situation at the unblocked interaxal differential for normal driving on all types of roads, from dry roads with a firm covering to wet roads, and also the roads covered with ice or snow. This position provides big economy, more silent driving, the smallest wear and the best driving.
Use this situation at the blocked interaxal differential for increase in draft, at feeling of loss of capacity, for example, when sliding wheels in the mode "N" with the unblocked interaxal differential.
«N» (neutral situation) To wheels it is not transferred to any capacity. Use this position only at management of the winch or other equipment. The car should be stopped.
«L» (the provision of lowering transfers, interaxal differential it is blocked) Use this situation for the maximum capacity and draft. Use situation "L" under trying conditions driving when the car badly gives in to management even in the mode "N" with the blocked interaxal differential.
Inclusion of a control lamp of blocking of interaxal differential testifies to blocking activation.
Keep in mind that if not To/l dies away by pressing of the button of blocking of interaxal differential, conduct the car directly at acceleration or delay or be developed.
Switching procedure
|
|
1. For switching between modes of an unblocking and blocking of a position of "N" press the button of blocking of interaxal differential.
2. For switching between H and L broadcasts stop the car, establish a transmission in the situation "N" and switch a control lever a drive to four wheels.
|
|
Never switch the lever of a regulator of a drive to four wheels in case of car sliding. Before carrying out switching, stop sliding or car spinning. |
|
|
System of blocking of forward and back differentials
|
|
1. The system of blocking of forward and back differentials is intended for use only in case of pro-slipping of wheels in a ditch or on the slippery or rough road. This system is effective in case of slipping of one of wheels or one right or one left pair of wheels.
|
|
Do not use blocking of back differential in the conditions which are differing from given above. Otherwise big efforts of a steering and careful management at performance of turns be required. Especially use of forward differential as addition to back extremely will complicate a steering and can lead to car drift during acceleration or engine braking. |
2. For blocking of back differential press and turn the switch clockwise, yet will not hear click. If it does not help, turn the switch clockwise against the stop to block forward differential in addition to the back.
3. On forget to stop the car before performance of blocking of differential.
4. For simple blocking turn the switch of blocking and carefully press an accelerator pedal.
5. If the switch is in the included situation, the control lamp will blink. Wait some seconds while the system will not finish operation. After the differential will be blocked, the control lamp will stop to blink and will constantly burn.
6. If the back differential is blocked, the anti-blocking brake system does not work. If the control lamp of "ABS" at this time lights up, it is normal.
|
|
Do not block differential until wheels will not stop slipping. Otherwise the car can move in the unforeseen direction if the differential is blocked that can lead to possible damage of components of blocking of differential. Do not drive the car for the speed over 8 km/h if the differential is blocked.
|
7. To unblock differential, turn the switch against the stop counter-clockwise.
8. Unblock differential as soon as the car will get under way from a place.
9. For a simple unblocking slightly turn a steering wheel in any direction at car movement.
10. If the differential is deduced from gearing, the control lamp will go out.
11. The differential will be also unblocked when switching the lever of a regulator of a drive on four wheels in the situation "N". Do not forget to establish the switch in the switched-off situation after use of this function.
12. For check of a display lamp turn the ignition key in the situation "ON", however do not start the engine. |
|
System of blocking of back differential
The system of blocking of back differential is intended for use only in case of pro-slipping of wheels in a ditch or on the slippery/rough road.
This system of blocking of differential is effective in case of slipping of one of back wheels.
|
|
1. For blocking of back differential press and turn the switch clockwise, yet will not hear click.
2. Do not forget to stop the car before performance of blocking of differential.
3. For simple blocking turn the switch of blocking and carefully press an accelerator pedal.
4. If the switch is in the included situation, the control lamp will blink. Wait some seconds while the system will not finish operation. After the differential will be blocked, To/l will stop to blink and will constantly burn.
5. If the back differential is blocked, the ABS system does not work. If at this time will light up To/l ABS system, it is normal.
|
|
Do not block differential until wheels will not stop slipping. Otherwise the car can move in the unforeseen direction if the differential is blocked that can lead to a road accident. It can lead to possible damage of components of blocking of differential also. Do not drive the car for the speed over 8 km/h if the differential is blocked. |
6. To unblock differential, turn the switch against the stop counter-clockwise.
7. Unblock differential as soon as the car will get under way from a place.
8. For a simple unblocking slightly turn a steering wheel in any direction at car movement.
9. If the differential is deduced from gearing, the control lamp will go out.
10. The differential will be also unblocked, if you switch the lever of a regulator of a drive to four wheels in the situation "N". Do not forget to establish the switch in the switched-off situation after use of this function.
11. For check of a display lamp turn the ignition key in the situation "ON", however do not start the engine. |
|
Control system of speed (Tempostat)
Function of a speed control allows to conduct the car on desirable speed over 40 km/h even if to clean a foot from an accelerator pedal.
Speed can be supported at higher or low level within the engine characteristic though little change of speed can occur upon transition to raising or lowering transfer. On abrupt slopes there can be a bigger change of speed therefore it is better to conduct the car without resorting to темпостату.
|
|
For ensuring the maximum control over movement of the car do not use темпостат when driving in the conditions of heavy traffic of transport either under changing traffic conditions or on slippery (wet, covered with ice or snow) roads, and also at a strong wind. Avoid increase in speed at movement down on descent. If speed of the car too fast, disconnect темпостат and pass to lowering transfer for use of braking by the engine for the purpose of delay.
|
Inclusion and system switching off
|
|
For management tempostaty press the CRUISE ON OFF button. Thus burning control lamp on a control panel will show that now it is possible to establish desirable speed of the car. By the second pressing the system will be switched completely off.
|
|
In order to avoid casual inclusion темпостата hold the CRUISE ON OFF switch switched off if you do not use темпостат. |
|
|
Choice of cruiser speed
|
|
1. Disperse the car till demanded speed, press a regulator down in the SET/COAST direction and release it, further the chosen high-speed mode will be supported tempostaty automatically.
2. If speed is not satisfactory, move the lever up for faster speed or move down for lower speed. Each otzhimaniye changes installation of speed to 1.6 km/h. After installation of speed it is possible to clean a foot from an accelerator pedal.
3. In need of acceleration for example, when overtaking clamp an accelerator pedal with sufficient force to exceed the established speed. If to release a pedal, the car will return to the speed established before performance of acceleration. |
|
Cancellation of the chosen high-speed mode
|
|
1. To cancel the chosen high-speed mode it is possible having pressed a brake pedal, or having pulled the lever in the CANCEL direction and having released it.
2. If speed of the car goes down below 40 km/h, the chosen high-speed mode will be automatically cancelled.
3. If speed of the car falls more than 16 km/h below the chosen value, cruiser installations also will be automatically cancelled.
4. If cancellation of the chosen high-speed mode occurs on any to other, excellent from listed above, the reasons, check the car at the representative of Toyota or Lexus at the first possibility. |
|
Return to a cruiser mode after compulsory decrease in speed
|
|
1. Press the lever up in the RES/ACC direction and take it in this situation. Release the lever when desirable speed will be reached. At that time while the lever will be pressed, the car will gradually speed up.
2. However rather to return to higher speed, it is necessary to accelerate a car course, and then to press the lever down in the SET/COAST direction. |
|
Return to a cruiser mode after compulsory acceleration
|
|
1. Press the lever down in the SET/COAST direction and take it in this situation. Release the lever when desirable speed will be reached. While the lever will be pressed, the car will gradually reduce speed.
2. However rather to return to lower speed, it is necessary to reduce speed of the car, and then to press the lever down in the SET/COAST direction.
3. Even if to switch off raising transfer at included темпостате, braking by the engine will not be carried out, because is not switched off темпостат. For reduction of speed of the car return to slower speed by means of the lever темпостата or pressing of a brake pedal. If the brake pedal is used, темпостат will be switched off. |
|
Renewal previously the established speed
|
|
1. If previously the established speed was cancelled by a way of switching of the lever of a regulator, or pressing of a pedal of a brake, by lever pressing up in the RES/ACC direction the speed established before cancellation will be restored.
2. However if speed of the car falls below 40 km/h, previously the established speed will not be renewed. |
|
Warning signal about malfunction in system темпостата
|
|
|
1. If the control lamp of "CRUISE" on a control panel blinks when using темпостата, press the CRUISE ON OFF button for system switching off, and then press the button again for system inclusion.
2. In case there will be one of the following actions, in темпостате there are malfunctions.
- The control lamp does not burn.
- The control lamp blinks again.
- The control lamp dies away after highlighting.
3. In this case address to the representative of Toyota for car check.
|
|
|
|