Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 of release

Repair and car operation


Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and receptions of safe operation of the car
+ Settings and routine maintenance of the car
+ Engine
+ Systems of cooling of the engine, salon and air conditioning heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
- Transmission line
   Specifications
   Driveshafts and hinges - the general information
   Check of a condition of the transmission line
   Removal and driveshaft installation
   Replacement of kardanny hinges
   Driving shaft/semi-axes, - the general information and condition check
   Removal and installation of semi-axes, bearings and epiploons of the back bridge
   Replacement of an epiploon of a leading gear wheel of differential
   Removal and installation of assembly of the back bridge
   Removal and installation of power shafts
   Replacement of protective covers and service of CV JOINTS
   Removal and installation of assembly of forward differential
   Removal and installation of naves with a disconnected drive
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




Removal and driveshaft installation

 PERFORMANCE ORDER

To Poddomkratta the car also establish it on props. Transfer a transmission to neutral situation. The parking brake do not cock.

Back driveshaft

Removal

Assembly of the back driveshaft is presented on an accompanying illustration.

Assembly of the back driveshaft


 PERFORMANCE ORDER

1. Put adjusting labels on all flanges and shlitsevy connections (address to an accompanying illustration) – in order to avoid balancing violation at assembly the shaft should be established strictly in the former situation.
2. Turn out bolts of fastening of a flange collar to back differential (address to an illustration above), for the purpose of ensuring access to the next bolt turn a shaft / back wheels.
3. Lower the back end of the driveshaft, then release fixture soyedinitelno a camshaft flange to a transfer case and liberate the forward end of a shaft from a box.

The description of procedures of replacement of kardanny hinges see in the Section Replacement of kardanny hinges. Replacement of epiploons of differentials, is described in the Section Replacement of an epiploon of a leading gear wheel of differential.

Installation

 PERFORMANCE ORDER

1. Carefully wipe a surface of a case of a transfer case round an entrance opening of the driveshaft. Attentively check an epiploon condition. Grease shlitsevy connections and crosspieces with multi-purpose greasing.
2. To Priboltita homutny assembly of the hinge to a connecting flange, having tightened fixture while only by hand.
3. Lift the back end of a shaft in regular situation, achieve combination of the landing labels put in the course of dismantle and fill in openings fixing bolts.
4. Tighten nuts of fixing bolts with demanded effort. Clean props and lower the car on the earth.

Forward driveshaft

Removal

Assembly of the forward driveshaft is presented on an accompanying illustration.

Assembly of the back driveshaft


 PERFORMANCE ORDER

1a. Give fixture and remove the top dustproof cover of a shaft (address to an accompanying illustration).
1b. Cнимите the bottom dustproof cover of a shaft (address to an accompanying illustration).
2. Mark position of the driveshaft of rather connecting flanges of a transfer case and forward differential.
3. Give nuts of fixing bolts (do not forget about washers) and remove the driveshaft.

The description of procedures of replacement of kardanny hinges is provided in the Section Replacement of kardanny hinges. Replacement of epiploons of differentials is described in the Section Replacement of an epiploon of a leading gear wheel of differential.

Installation

 PERFORMANCE ORDER

1. Connect the forward end of a shaft to a connecting flange of differential. By hand tighten nuts of fixing bolts.
2. Having as appropriate modified length of a shaft, connect its back end to a flange of a transfer case. Tighten fixture with demanded effort.
3. Establish into place dustproof covers of a shaft.
4. Clean props and lower the car on the earth.